Pingxiang Zhongci Environmental Ceramics Material Co.,Ltd.

How to choose Packings

Mar 14, 2024 Leave a message

The selection of packing includes determining the type, specification and material of filler. The selected filler should not only meet the requirements of the production process, but also make the equipment investment and operating costs minimum.

Selection of packing type

info-495-495

 

How to choose Packings?

The selection of packing includes determining the type, specification and material of filler. The selected filler should not only meet the requirements of the production process, but also make the equipment investment and operating costs minimum.

Selection of packing type

1)Considering the requirements of the separation process, the following aspects are usually considered:

2)In general, the mass transfer efficiency of structured fillers is higher than that of bulk fillers.

3)The flux needs to be large. On the premise of ensuring high mass transfer efficiency, fillers with high flooding point gas velocity or gas phase kinetic energy factor should be selected.

4)The pressure drop of the packing layer should be low.

5)The filler has strong anti-fouling performance, convenient disassembly and maintenance.

 

2,Selection of packing specifications.

Packing specification refers to the nominal size or specific surface area of the packing.

❶ Selection of bulk packing specifications

The bulk fillers commonly used in industrial towers are mainly DN16, DN25, DN38, DN50, DN76 and other specifications.

Similar fillers, the smaller the size, the higher the separation efficiency, but the resistance increases, the flux decreases, and the cost of fillers also increases a lot. However, when large size packing is used in small diameter tower, it will produce poor liquid distribution and serious wall flow, which will reduce the separation efficiency of the tower.

Therefore, there should be a regulation on the ratio of the tower diameter to the packing size, and the ratio D/d of the general tower diameter to the nominal diameter of the packing should be greater than 8.

❷ Selection of structured packing specifications

There are many ways to express the types and specifications of structured fillers commonly used in industry, and the specific surface area is used in China, mainly 125, 150, 250, 350, 500, 700 and other specifications.

The same type of structured filler, the larger the specific surface area, the higher the mass transfer efficiency, but the resistance increases, the flux decreases, and the cost of the filler increases significantly.

Selection should be from the separation requirements, flux requirements, site conditions, material properties and equipment investment, operating costs and other aspects of the comprehensive consideration, so that the selected filler can meet the technical requirements, but also have economic rationality.

info-609-609

 

3,Selection of packing material

The material of the packing is divided into ceramic, metal and plastic three categories.

❶ Ceramic packing

info-1143-563

Ceramic filler has good corrosion resistance and heat resistance, ceramic filler is cheap, has a good surface wettability, brittle, fragile is its biggest disadvantage. It is widely used in gas absorption, gas washing, liquid extraction and other processes.

❷ Plastic Packing

info-1143-957

The materials of plastic fillers mainly include polypropylene (PP), polyethylene (PE) and polyvinyl chloride (PVC), etc., and polypropylene is generally used in China. Plastic fillers have good corrosion resistance and can withstand the corrosion of general inorganic acids, alkalis and organic solvents. It has good temperature resistance and can be used below 100℃ for a long time.

Plastic fillers are light, cheap, have good toughness, impact resistance, not easy to break, and can be made into thin-walled structures. Its flux is large, the pressure is reduced, and it is used in absorption, desorption, extraction, dust removal and other devices.

The disadvantage of plastic fillers is that the surface wettability is poor, but the surface wettability can be improved by proper surface treatment.

❸ Metallic packing

info-1268-1268

Metal packing can be made of a variety of materials, the main consideration when choosing corrosion problems.

Carbon steel packing has low cost and good surface wettability, and should be prioritized for non-corrosive or low-corrosive materials.

Stainless steel packing has strong corrosion resistance, generally resistant to corrosion of common substances other than Cl-, but its cost is high, and the surface wettability is poor, in some special occasions (such as very low spray density under the vacuum distillation process), the surface needs to be treated to achieve good results.

Titanium, special alloy steel and other materials made of filler cost is very high, generally only in some highly corrosive material system used.

Generally speaking, metal fillers can be made into thin-wall structures, which have large flux, small gas resistance, and high impact resistance, and can be used at high temperature, high pressure, high impact strength, and the most widely used.

 

Summarize:

When selecting fillers, for a particular application, the best standard for fillers is based on the properties expected of the composite material, and the following basic principles must be taken into account.

1, the filler must maintain its original structure during processing, and maintain inertia, insolubility, thermal stability, non-volatility, no catalytic activity and low adsorption.

2, the filler must be compatible with the substrate, non-corrosive.

3, easy to handle, high packing density, low moisture content, low dust, non-toxic.

4, must be easy to obtain, sufficient supply, moderate price, stable quality.